engine oil capacity RENAULT TWINGO RS 2009 2.G Engine And Peripherals Workshop Manual

10A-22
ENGINE AND CYLINDER BLOCK ASSEMBLY
Engine oil: Draining - Refilling
D4F or D7F
10A
PARTS AND CONSUMABLES FOR THE
REPAIR WORK
aParts always to be replaced :
-copper seal.aConsumable (see Vehicle: Parts and consuma-
bles for the repair) (04B, Consumables - Products).
-Engine oil (see Engine oil: Specifications) (Tech-
nical Note 6013A, 04A, Lubricants).
I - OIL SERVICE
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment). Special tooling required
Mot. 10188 mm square engine drain
plug spanner.
Equipment required
oil change wrench
oil recovery tray
torque wrench
oil change end piece with an 8 mm square drive
Tightening torquesm
drain plug20 N.m
EngineAverage oil capacity
(adjusting using dipstick) (l)
Oil change with-
out filter
replacementOil change with
filter replace-
ment
D7F
3.8 4
D4F
WARNING
Always check the oil level using the dipstick.
Do not exceed the maximum level on the dipstick
(could destroy the engine).
Correct the engine oil level if necessary before
deliver ing the vehicle to the customer.
Note:
When topping up the engine oil, always leave at
least 10 minutes before checking the level with a
dipstick.

10A-25
ENGINE AND CYLINDER BLOCK ASSEMBLY
Engine oil: Draining - Refilling
K4M
10A
I - RECOMMENDATIONS FOR REPAIR
aDirection of fitting for a drain plug seal.For a sheet metal engine oil sump
aThere is no direction of fitting for a seal fitted with a
rubber lip.
II - PARTS AND CONSUMABLES FOR THE REPAIR
aparts always to be replaced: Drain plug seal on
engine oil sump.
aconsumable:
-engine oil (see Engine oil: Specifications) (Tech-
nical Note 6013A, 04A, Lubricants). Equipment required
oil recovery tray
oil change wrench
torque wrench
oil change end piece with an 8 mm square drive
Tightening torquesm
engine oil sump drain
plug20 N.m
EngineAverage oil capacity (adjust with
dipstick) (l)
DrainingOil change
plus oil filter
replacement
K4M4.9 5
113765
IMPORTANT
Wear leaktight gloves (Nitrile type) for this opera-
tion.
WARNING
Always check the oil level using the dipstick.
Do not exceed the maximum level on the dipstick
(could destroy the engine).
Correct the engine oil level if necessary before
delivering the vehicle to the customer.
Note:
When topping up the engine oil, always leave at
least 10 minutes before checking the level with a
dipstic k.

10A-27
ENGINE AND CYLINDER BLOCK ASSEMBLY
Engine oil: Draining - Refilling
K9K
10A
I - PRECAUTIONS FOR REPAIR
aThere is no direction of fitting for a seal fitted with a
rubber lip.
II - PARTS AND CONSUMABLES FOR THE REPAIR
WORK
aparts always to be replaced: Drain plug seal on
engine oil sump.
aConsumable:
-engine oil (see Engine oil: Specifications) (Tech-
nical Note 6013A, 04A, Lubricants). Special tooling required
Mot. 10188 mm square engine drain
plug spanner.
Equipment required
oil recovery tray
oil change wrench
oil change end piece with an 8 mm square drive
Tightening torquesm
the drain plug20 N.m
Engine SuffixAverage oil capacity
(adjusting using dipstick) (l)
Oil change
without fil-
ter replace-
mentOil change
with filter
replacement
K9K740 4.3 4.4
718 4.5 4.6
113765
IMPORTANT
Wear leaktight gloves (Nitrile type) for this opera-
tion.
WARNING
Always check the oil level using the dipstick.
Do not exceed the maximum level on the dipstick
(could destroy the engine).
Correct the engine oil level if necessary before
delivering the vehicle to the customer.
Note:
When topping up the engine oil, always leave at
least 10 minutes before checking the level with a
dipstic k.